Chic Knits Downloadable Knitting Patterns Chic Knits Downloadable Knitting Patterns Chic Knits Knitting Blog Chic Knits Knitting Tips & Techniques Chic Knits Bonne Marie Burns Free Knitting Patterns
Studio Chic Knit Blog


Tuesday, July 24, 2007

when is Non-Progress, Progress?

When it’s a L.E.S.S.O.N.

Being that I am a charter student of the School of Hard Knocks, sometimes lesson becomes lessonS and it takes quite a few rounds, erm, rows before I get it.

My *Groovy Condo* shell is promising to be one of the most challenging lessons of all.

I picked it out of my pile of UFO’s for a couple of reasons — you all gave it quite a few votes of confidence in the Resurrection Poll a few weeks (!) ago and I really liked the design. It seemed very close to the finish line: a couple of inches of knitting on the Front; edging around the armholes; side seams; then a knitted band around the top.

It seemed the natural opposite/companion to the shawl project I’m working on: one is minute gauge; one is ginormous gauge. So we bit.

Here you can see the seaming went quite well — I was concerned about those wacky condo stitch areas — how the heck was that going to go together and not look ridiculous? My first choice was regular sewing thread and I was going to anchor Front-to-Back loops with some almost invisible thread loops.

But once I got going on the seam itself (regular old mattress stitch through the tubular cast-on areas and St st) ye olde light bulb poPPed!

All I had to do was use a length of my seaming ribbon (hmm, yarn) to make a singular bridge between the two St st sections. You know you have the right side of the piece facing you when you mattress stitch, but when I got to the condo areas, I stuck the needle in and flipped to the wrong side and made a small knot on the side of the seam. Then I smoothed out an equal amount of length with my seaming yarn to match the height of the condo stitch, held it flat with my finger and made another small knot on the top side of the stitch. This made an anchor between seaming areas (top and bottom of Condo Area #1). SMOOTH. Invisible. No extra work! Then I just continued mattress stitching to the next condo area and repeated.

So the sides of the piece are flexible and hang fluidly. Whew! To Inifinity And Beyond, people!

Got those armhole edgings done, check.

Got the Neckline Border done. Bleck!

Now came the fun part, but only if you are a process knitter! This design from Fatto a Mano #146 (using *Poesie* ribbon) calls for a ribbed neck finish. You work it sideways, then seam it on the piece. Ah, no. Thank. You.

I decided to knit it on as I went but the concept exploded because of the HUGENESS of the GAUGE! Ususally, I just get up to the edge in question with my band and SSK or K2TOG with a loop I pull through the body piece on every RS row. Approximately. After about 9 failed attempts, don’t ask me why this went on like a scratched and heaving record sometimes knitting is like that, I went and got another needle and picked up my neckline stitches (which should’ve been left *live* to begin with but were sadly, bound-off). Then it was a breeze to SSK or SSP with the last/first st on the band side and attach! QUE? Making those stitches with the working yarn made a messy edge; making the edge with the *3rd party* stitches make it smooth.


knitting patterns


 
 
©2001-2014 Bonne Marie Burns
All Rights Reserved
Unauthorized reproduction in any form prohibited.

Site Design: BigBrain Multimedia/Bonne Marie Burns

"ChicKnits" and "Chic Knits" are the ®Registered Trademarks of Bonne Marie Burns of Portland OR